Carbon Fiber Extreme

debotech

2020 Chevy Corvette review: Testing the $59,995 C8 Stingray

Spoiler alert: Chevrolet’s fabled $60K C8 Corvette is the performance bargain of the year.

2020 Chevy Corvette
The no-cost Ceramic paint is fantastic.Steven Ewing/Roadshow

More than its 3-second 0-to-60-mph time, its 1.0 G of cornering grip or the fact that, you know, its engine sits behind the cockpit, the craziest thing about Chevrolet’s new C8 Corvette Stingray is that everything I just mentioned comes on a wildly styled sports car that costs $59,995 — including the delivery fee. No other car offers so much performance for so little cash.

Real quick, though, I need to be honest: I kind of figured the $59,995 Corvette would be the car world’s white whale. You know, the C8 that grabs headlines for its low MSRP even though the reviews all feature more generously specced 3LT Z51 models, like the nearly $87,000 example Andrew Krok just tested, the one Tim Stevens took to the track or the one Chris Paukert first drove last year. I assumed it’d be like the headline-grabbing-but-nowhere-to-be-found $35,000 Tesla Model 3. So, good on Chevy for calling my bluff and sending me the no-options, $59,995 Corvette seen here. Because now I can say it again, and this time with feeling: No other car offers so much performance for so little cash.

The base 2020 Chevy Corvette is a whole lot of car for $60K

2020 Chevy Corvette

2020 Chevy Corvette

The base Corvette 1LT has the same 6.2-liter naturally aspirated V8 as every other Stingray, with 490 horsepower and 465 pound-feet of torque. Working through an eight-speed, dual-clutch automatic transmission, the rear-wheel-drive Corvette will accelerate to 60 mph in 3 seconds flat, and do so without any overdramatic or skittish tendencies. Even on its stock all-season tires, the wide, 305/30-section rear rubbers simply claw into the pavement and shoot the Stingray forward.

The V8 sounds freakin’ awesome on full boil near its (relatively low) 6,500-rpm redline, even without the performance exhaust. I don’t like the transmission’s paddle shifters — most automakers get these wrong — but they’re a direct link to the quick-shifting DCT, which is also perfectly tuned when left to its own devices. The steering is communicative and nicely weighted, letting me know exactly how much grip those all-season tires have. And the standard limited-slip differential means power is appropriately distributed at the rear axle, so you can goose the throttle coming out of a corner without breaking the back end loose. The brakes are strong and offer confident, composed stopping without fade. The standard chassis tune is really good, too — comfortable when you need it to be but nicely taut when it counts.

The key thing you miss out on with the base Corvette is the almighty Z51 pack, which includes larger Brembo brakes and Chevy’s Magnetic Ride Control suspension with adaptive damping and performance traction management tech. You also can’t get the sportier exhaust, which in turn unlocks an additional 5 hp and 5 lb-ft and actually pushes the Corvette’s 0-to-60-mph time below the 3-second barrier, as if this car wasn’t already holy-smokes quick.

2020 Chevy Corvette
The Michelin Pilot Sport all-season tires are perhaps the only limitation of the 1LT package.Steven Ewing/Roadshow

But here’s the thing: On several runs along my usual canyon test route north of Los Angeles, nothing about this base Corvette lets me down. It’s clear that even the most stripped-down C8 is a fantastic driver’s car through and through. In fact, it’s one of the most memorable sports cars I’ve tested this year — especially at this price. Frankly, all the Corvette most people really need.

The only real limitation here is the choice of all-season tires. But even then, I don’t think the majority of Corvette owners will ever exceed the limits of what the Michelin Pilot Sport rubbers can muster (Chevy says they’re good for 1.0 G of lateral grip, remember). If for some reason you find yourself needing something stickier, a whole slew of summer options are available from tire shops around the country. Besides, a $1,500 set of Pilot Sport Cup 2s is slightly easier to justify on what is, effectively, a $60,000 supercar.

And I do mean supercar. Just look at this thing; not a single part of the 1LT’s appearance says “base Corvette.” You get the same staggered 19-inch front and 20-inch wheels as other trims, and I don’t have any qualms with the standard silver-painted look. Every Corvette comes with sharp LED headlamps and nothing about the long, low, wide proportions changes from model to model.

2020 Chevy Corvette

The Corvette’s interior is hardly basic, with perforated leather wrapping the standard GT1 seats. And while these chairs aren’t as comfortable as supportive as more expensive GT2 and GT3 options, I can’t find a reason to complain. The seating position is excellent and never leaves me sliding around during spirited driving. The leather-wrapped steering wheel feels great, too, though I hate its squircle shape, which doesn’t really lend itself to nine-and-three hand placement.

As far as in-car tech is concerned, the Corvette offers some of GM’s best. That 12-inch digital gauge cluster is standard across the board and it looks awesome, with colorful, reconfigurable displays. Move to the center stack and Chevy’s Infotainment 3 setup is housed on a eight-inch, high-definition touchscreen. Upper trim levels include embedded navigation, but the C8 comes standard with Android Auto and Apple CarPlay, so if you have a phone and a USB cable, you’re all set.

2020 Chevy Corvette
The Corvette kind of needs the Z51’s wing to make the rear end work, but even without it, the Stingray will never fail to turn heads.

Taken as a whole, however, the 2020 Corvette Stingray 1LT is a sports-car bargain that’s absolutely unmatched. Chevrolet’s more expensive versions offer more creature comforts and widen the performance envelope, sure, but I’ll be damned if this base Corvette isn’t hugely impressive in its own right. Good luck finding a comparable experience for $59,995 out the door.

Steven Ewing for CNET


Test Drive: The 2020 Chevrolet Corvette Stingray rocks

The first mid-engine production Corvette was six decades in the making

The 2020 Chevrolet Corvette Stingray is a rock star car. I don’t mean that figuratively. An actual rock star owns one.

Chevrolet

Kiss frontman Paul Stanley picked up a white Stingray with a red interior and tweeted his love for it, saying he bought American because it’s beyond “world class.”

OK, perhaps the fact that he’s buds with General Motors President Mark Reuss influenced his purchase, but he’s driving it, so the endorsement is legit.

Chevrolet

Of course, the 68-year-old singer does fit the classic stereotype of a Corvette buyer: mature with money to burn. Just the type of customer many expected to be alienated by the Corvette’s switch from a front- to mid-engine design. So much for that.

The Chevrolet Experimental Research Vehicle, or CERV I, was revealed in 1960 to explore the possibilities of a mid-engine layout.
The Chevrolet Experimental Research Vehicle, or CERV I, was revealed in 1960 to explore the possibilities of a mid-engine layout.

The eighth-generation Corvette is the realization of a dream that dates back six decades, when legendary GM engineer Zora Arkus-Duntov started building mid-engine prototypes because the layout offered potentially better performance than a front-engine design. It’s an idea that race and exotic car builders took and ran with while Chevy stuck to tradition.

The 1990 CERV III never made it into production but could be driven in the video game "Test Drive III: The Passion."
The 1990 CERV III never made it into production but could be driven in the video game “Test Drive III: The Passion.”

Arkus-Duntov’s team and its predecessors developed over the years, but the executives at HQ just couldn’t be convinced. Current Corvette Executive Chief Engineer Tadge Juechter told Fox News Autos that a mid-engine Corvette was rejected as recently as 2006 simply because of inertia.

“There were people when we first started talking about this that were almost entirely naysayers. Virtually nobody in leadership thought it was a good idea because we were building and selling Corvettes to an enthusiastic fan base, or selling them in volumes to make a profit,” he said.

Cooler heads  prevailed as the seventh-generation Corvette was completed for 2014, and Juchter and his team were off to the races, even though none of them had ever worked on a mid-engine car before. You’d never know it.

Chevrolet
Chevrolet

The new Stingray is a radical departure from previous editions, but it keeps many classic Corvette traits intact, including a relatively low starting price of $59,995. Some of the bodywork is technically fiberglass, but in various modern composite forms. Jucther calls it a “mosaic” of materials, which also applies to a chassis made from aluminum, steel, magnesium and a touch of carbon fiber.

(Fox News Autos)

Then there’s the rear trunk, which you don’t often find in a mid-engine car. It’s big enough to fit the lightweight, removable roof panel or two golf bags, because the latter capability may be even more entwined with the Corvette’s image than the location of its motor. Since that’s in the middle of the car, there’s also room for a sizeable front “frunk.”

Chevrolet
Chevrolet

The Stingray’s interior is equally practical, as far as low-slung sports cars are concerned, with enough legroom for the 6-foot-tall Stanley to fit comfortably, perhaps even while he’s wearing his sky-high stage boots. It’s well-trimmed and designed with a lot of interesting details, like panels hovering over the top of the dash, and is more appealing than the cabins in some far more expensive cars, including the $450,000 Ford GT’s stark accommodations.

Chevrolet
Chevrolet

Its one controversial element is a long row of climate control buttons on a buttress separating driver and passenger that can be awkward to use. However, the tablet-style infotainment screen, which is a close reach, has redundant on-screen controls that you can operate with your thumb while you steady your hand on the bezel.

A second display serves as the instrument cluster, which is configurable and framed by a squared-off steering wheel that stays below your line of sight as you look over the low dashboard and through the absolutely panoramic windshield. The over-the-shoulder views aren’t anywhere near as good, but the rearview mirror is equipped with a video feed, and if you turn your head all the way around you can see the engine behind the window. It’s a glorious sight.

Chevrolet

The Stingray is powered by GM’s latest 6.2-liter pushrod V8. Yes, pushrods. Just like the Chevy Silverado. Except this one is presented in all of its mechanical glory with parts designed to be displayed under the humongous hood’s glass panel.

The V8 gains 35 horsepower over the outgoing version for 490 hp and has 465 lb-ft of torque to go with it. A toggle and pushbutton-controlled 8-speed dual-clutch automatic transmission is standard and the only type available, but it does come with paddles behind the wheel that let you shift gears manually. If you pull them both at the same time it instantly switches to neutral so you can rev the engine for your audience. There will always be one, because the Stingray’s chiseled body has all the presence and drawing power of a million-dollar exotic.

The $5,000 Z51 performance package on my test car tweaks the engine to 495 hp and 470 lb-ft and adds extra cooling for the engine and transmission, a track-oriented suspension tune, downforce-producing rear wing and body extensions, larger Brembo brakes, a limited-slip rear differential and a set of sticky summer tires.

The car was also equipped with GM’s Magnetic Ride Control adjustable shocks, which are worth it on any model they are available on, from trucks to sedans, even for the $1,895 they cost here. Just as valuable, but for a very different reason, is the optional $1,495 hydraulic system that raises the Stingray’s pointy nose 2 inches to avoid scrapes and can be programmed to do that automatically as you approach up to 1,000 marked locations where you often drive.

Although billiard table-smooth roads are preferred, a Stingray configured like this and set to Tour mode can be used as a daily driver on the most wretched pavement, even with its ridiculously low-profile tires and staggered 19- and 20-inch wheels. The car just glides over them with no shakes, rattles, rolls or flexes. But the Stingray can flex when you want it to.

Chevrolet

Drop the hammer and 60 mph arrives in about 2.9 seconds without any wheel spin, according to Chevrolet. That’s thanks in part to the 40/60 weight distribution provided by the mid-engine design and the Stingray’s excellent traction management system. It’s nearly as quick as the old front-engine 755 hp Corvette ZR1, which was a big part of the reason Chevy made the switch.

The other becomes apparent when the road gets curvy. Moving the weight between the wheels improves steering response and helps neutralize the handling, which is like a slot car’s up to the limit. I didn’t get the opportunity to find out what happens when you go past it, but I can tell you that there is a long way to go to get there.

The Stingray plays good music while you do all this. Jucther said refining the engine sound with it located right behind your ear was one of the tougher challenges posed by the layout.

“The nice thing about a front-engine car is that you’ve got induction noise in the front and the exhaust pipe in the back, so you’ve got a kind of stereo,” he said. All I can say is: expert-level challenge complete.

The transmission can be a little lazy to shift in Tour but rips through the gears and always picks the right one in the Sport and Track modes, which also adjust the throttle response and firm up the suspension and steering feel. You can customize everything to your liking and engage your settings with a Z-mode button on the steering wheel if you prefer.

Chevrolet

The reimagined Stingray now nearly exists in a class by itself. The cars closest to it on price and execution are the mid-engine Porsche 718 and the rear-engine Porsche 911, but neither are quite the same thing. As far as six-figure, mid-engine cars like the Audi R8, Acura NSX and Lamborghini Huracan are concerned, despite their power advantage and all-wheel-drive, I’d be hard-pressed to give you a truly good reason to spend triple your money on one.

Those arguments won’t even hold much longer against the Corvette, because you know there are much more powerful models on the way. Juechter won’t even hint at how much, but word on the street is that 800-1,000 hp isn’t out of the question, possibly with an electric boost. Based on the Stingray’s performance, the platform has plenty of room to grow.

But regardless of what’s to come, the car on sale today makes one thing perfectly clear:

This Detroit city automaker still knows how to rock.

———-

2020 Chevrolet Corvette Stingray

Type: 2-passenger, 2-door, rear-wheel-drive coupe

Base price: $59,995

As tested: $80,315

Engine: 6.2-liter V8

Power: 495 hp, 465 lb-ft

Transmission: 8-speed dual-clutch automatic

MPG: 15 city/27 hwy

Gary Gastelu for Fox News


There’s Good News For Anyone Wanting A New Corvette

2020-2021 Chevrolet Corvette C8 Front View

Building enough to meet demand is key.

The era of the C8 Chevrolet Corvette got off to a rocky start. First, there was the five-week-long UAW strike against GM. And then came the coronavirus pandemic. As a result, not every 2020 Corvette order can be fulfilled. To help settle down anxious buyers who missed out this year, Chevrolet decided not to increase the 2021 Vette’s base price and those customers are now first in line. But there’s still one very specific way Chevy can boost C8 production that it has yet to do: add a second production shift.

According to Corvette Blogger, the Bowling Green, Kentucky Corvette plant has just initiated that second shift. These second shift workers had been in training alongside their first shift colleagues for some time before the pandemic struck.2020-2021 Chevrolet Corvette C8 Front Angle View2020-2021 Chevrolet Corvette C8 Side View2020-2021 Chevrolet Corvette C8 Rear-Facing View

The factory shut down delayed their training. But now they’re up and running, although not quite at full capacity because plant managers are still in final coordination with supply chain vendors to guarantee a steady flow of parts. Fortunately, these managers anticipated such a scenario months ago and decided to stock up on extra parts beforehand.

However, not all vendors are back to normal operating conditions and management isn’t too wild about dipping into their extra parts supply just yet. It’s best to give suppliers a bit more time because once those extra parts are used up, that’s it.Best Cars For City Driving In 20206 Performance Models Ford Needs To Bring Back

2020-2021 Chevrolet Corvette C8 Engine Bay

The Cor

2020-2021 Chevrolet Corvette C8 Engine Bay

vette Assembly Plant can reportedly build 95 Corvettes per shift, but employees have been working especially hard lately by dedicating more hours to increase that figure to about 116 cars per day. Once the second shift fully comes online along with zero supply chain issues, at least 190 vehicles per day can be expected. Last May, Chevy confirmed a total of 20,181 Corvette orders had been received and the initial plan was to build 20,000 units before the 2021 model year.

Obviously that isn’t happening now but the fact the second shift is now underway is a promising sign.

JAY TRAUGOTT  car buzz


Corvette Ranks in Top 10 of Most Awarded Cars from KBB

2020 Chevrolet Corvette Stingray
2020 Chevrolet Corvette Stingray
Photo: Chevrolet

Auto experts and journalists spend hours and hours evaluating every aspect of a vehicle so you have a road map to the models that will work best for you. The Chevrolet Corvette repeatedly rises to the top of lists and brings home the awards. According to the editors at Kelley Blue Book, the 2020 Chevrolet Corvette is one of the pub’s 10 most awarded cars of 2020.


Prestigious Win: Corvette Stingray named MotorTrend Car of the Year


The 2020 Chevrolet Corvette earned the seventh spot on the KBB list.

Primis Player Placeholder

“When it was unveiled, the all-new mid-engine 2020 Chevrolet Corvette nearly broke the internet,” writes KBB writer Allyson Harwood. “Its supercar styling and power numbers were impressive, but its incredible resale value data and bargain starting price make the Corvette far more than just an excellent sports car.”

Corvette attracting younger drivers
2020 Chevrolet Corvette Stingray
Photo: Chevrolet

The 2020 Chevrolet Corvette relishes a top speed of 194 miles per hour and thunders across the pavement with the strength of 495 horsepower and 470 lb-ft of torque. In a blink of an eye, approximately 2.9 seconds, the 2020 Corvette hits 60 mph.


Available Now: 2020 Chevrolet Corvette


In addition to KBB’s honors and praise, the 2020 Chevrolet Corvette earned the 2020 North American Car of the Year title and a Wards Auto 10 Best Award for the interior. The Chevrolet Corvette Stingray took home the 2020 MotorTrend Car of the Year award. The Detroit Free Press gave the Chevrolet Corvette C8 its inaugural title of Car of the Year. It is a 2020 Car and Driver 10Best and a 2020 Edmunds Top Rated Award winner in the sports car category. KBB recognized the Corvette’s value, giving it a 2020 KKB.com Best Resale Value award.

Source: DeAnn Ownes; TheNewsWheel


Corvette Scores Fourth Straight Win; Auberlen Makes History

Rick Dole/ IMSA

Antonio Garcia, Jordan Taylor hold on for Corvette Racing’s fourth straight win…

Corvette Racing has scored its fourth consecutive IMSA WeatherTech SportsCar Championship class victory following late-race drama for Porsche in Saturday’s Michelin GT Challenge at Virginia International Raceway.

Bill Auberlen, meanwhile, became the winningest driver in IMSA history with a long-awaited victory in GT Daytona.

Antonio Garcia limped the No. 3 Chevrolet Corvette C8.R to the win in the two-hour and 40-minute GT-only contest despite a loose floor on his mid-engined machine.

Garcia took over the lead when the pole-sitting No. 911 Porsche 911 RSR-19 of Nick Tandy was forced into the pits due to a left-rear tire issue with 18 minutes to go.

Co-driver Fred Makowkecki had rebounded from an early left-rear puncture to take over the lead thanks to a fuel-only stop during the race’s second full course caution.

A pit lane miscue with tightening the right-rear wheel saw Jordan Taylor lose time during the same round of stops but benefitted from misfortunes from both CORE autosport-run Porsches.

The No. 912 car of Earl Bamber battled a loose diffuser, caused by contact with the No. 25 Team RLL BMW M8 GTE of Connor De Phillippi, relegating the defending GTLM champions to a fifth place class finish after multiple stops for repairs.

Tandy and Makowiecki ended up finishing third, despite the Englishman nearly getting around the No. 25 BMW of Bruno Spengler on the final lap.

Up front, it marked Garcia and Taylor’s third win in the last four races and has extended their championship lead. 

The No. 4 Corvette of Tommy Milner and Oliver Gavin, who had an off-course excursion with 1 hour and 32 minutes to go, came home fourth in a race that saw nearly every GTLM car hit trouble.

It included the No. 24 BMW, which lost nearly 20 laps in the opening hour due to a mechanical issue.

Auberlen Makes History With 61st IMSA Win

Turner Motorsport claimed top class honors in GT Daytona, with Auberlen and Robby Foley winning for the first time in nearly a year.

Foley led from the early stages of the race before handing over the No. 96 BMW M6 GT3 to Auberlen with one hour to go.

While coming under attack from the No. 86 Meyer Shank Racing Acura NSX GT3 Evo of Mario Farnbacher, a mistake by the German under braking into Turn 1 initially dropped him to fourth.

Farnbacher managed to charge his way back to second, getting by the No. 48 Paul Miller Racing Lamborghini Huracan GT3 Evo of Bryan Sellers on the final lap through traffic.

Auberlen, meanwhile, became the most successful driver in IMSA competition, with his 61st win.

It marked Turner’s first class win since Motul Petit Le Mans last year when Auberlen tied Scott Pruett with all-time wins at 60.

Sellers and co-driver Madison Snow completed the GTD podium in third, ahead of the No. 74 Riley Motorsports Mercedes-AMG GT3 Evo of Gar Robinson and Lawson Aschenbach, who was in the fight for second in the closing laps.

The No. 14 AIM Vasser Sullivan Lexus RC F GT3 of Jack Hawksworth and Aaron Telitz completed the top-five in class.

RESULTS: Michelin GT Challenge


No. 3 Corvette C8.R Takes Third Win Of 2020 As C8.R Continues To Dominate IM

#3 Corvette Racing Corvette C8.R, GTLM: Antonio Garcia, Jordan Taylor

2020 has been a hard year for a lot of folks, but it’s been pretty smooth sailing for No.3 Corvette C8.R drivers Jordan Taylor and Antonio Garcia. The pairing gave Corvette Racing its first victory with its new Corvette C8.Rearlier this year at Daytona and promptly backed it up with another win at Road America shortly after.

Now the No. 3 Corvette C8.R has taken its third win of 2020 after Taylor and Garcia took victory in Sunday’s Michelin GT Challenge at Virginia International Raceway. The victory was unexpected, with Garcia only moving into the lead in the closing laps of the two-hour, 40-minute race. The No. 911 Porsche of Nick Tandy looked like a shoe-in for the win and was leading with just 18 minutes remaining when the Core Autosport-run entry cut a left rear tire, forcing Tandy to come into the pits.

Garcia then held off the No. 25 BMW M8 GTLM of Bruno Spengler and the hard-charging Porsche of Tandy, who was now on fresh rubber, to take the victory. If the race was any longer, Garcia may not have made it, with the No. 3 Corvette C8.R suffering heavy high-speed vibrations in the latter stage of the event. The Corvette Racing crew later sourced the cause of the vibrations to a broken rear diffuser, but without knowing what the cause of the issue was, the Spaniard was understandably concerned while behind the wheel.

“It took me a little bit (to know what was wrong), but the whole car was shaking a lot,” he said. “About 200 kph, the whole car was shaking a lot. It was coming from the rear.”

“I thought it was terminal because it was vibrating really bad,” he added. “But once I got used to it and knew it wasn’t interfering with the performance, I knew I could handle it. With the gap I could manage to the BMW. It was stressful not knowing what would happen if the rear diffuser would have fallen off, but the C8.R held on.”

Garcia also praised the Corvette C8.R for retaining a good degree of downforce and drivability even without a rear diffuser.

“So, the C8.R is also good with almost no rear diffuser or rear splitter. I’m very proud of that,” he said. “Very proud that everything stayed in one piece even though it was very challenging to drive there at the end.”

Spengler crossed the finish line second in the No. 25 BMW, while Tandy completed the podium after setting the fastest lap of the race on his charge back to the front. The No. 4 Corvette C8.R of Tommy Milner and Oliver Gavin finished fourth after Gavin went off-track following a restart earlier in the race.

Click here for full results from the 2020 Michelin GT Challenge from VIR.

Subscribe to GM Authority for more Indy 500 newsIndyCar newsmotorsports news and around-the-clock GM news coverage.

Sam McEachren for GM Authority


Chevrolet Has Built 1,750,000 Corvettes

The 1,750,000th Corvette is white and red, paying tribute to the 1953 original. It’ll be raffled off later this year.

NATIONAL CORVETTE MUSUEMFACEBOOK

Last Friday, without much fanfare, Chevrolet built Corvette No. 1,750,000. It’s an Arctic White coupe, with an Adrenaline Red interior—a spec paying homage to the 1953 Vette—and there’s a chance it could be yours.

The National Corvette Museum announced last month that this particular Corvette would be raffled off, and it’s selling 1500 virtual tickets at $200 a pop. A drawing will be held on September 4, and until then, Corvette #1,750,000 will live in the Museum alongside the millionth (a 1992 convertible) and the 1.5 millionth (a 2009 convertible) Vettes. Hopefully this one doesn’t end up in a sinkhole. All the proceeds from the raffle will be donated to the Museum.

Corvette No. 1,750,000 is extremely well equipped. It’s got the 3LT package along with the must-have Z51 Performance Pack, a front-end lift, the Engine Appearance Package, and a handful of other options. It’d cost you at least $81,000 to order a similar 2020 Corvette, so suddenly, a $200 raffle ticket doesn’t seem like such a bad deal.

corvette 1,750,000

NATIONAL CORVETTE MUSEUM FACEBOOK

Given that the very first Corvette was built on June 30, 1963, it took Chevrolet 67 years, one month and 15 days to build 1,750,000 examples. Not bad for a sports car. For context, it took Porsche 53 years to build a million 911s, and Mazda 26 years to produce its millionth Miata. Ford has built over 10,000,000 Mustangs, but that’s not a true sports car like a Corvette. Nissan reached the million Z-Car milestone sometime in the early Nineties, but even still, the Corvette has to be the most popular sports car of all time.

“This type of milestone only comes around every 10 or so years for Corvette,” said Kai Spande, head of the Bowling Green plant. “For this landmark achievement to also be one of the early mid-engines is just awesome for us and for our customers. It’s an amazing time to be part of the Chevrolet brand.”

At the time of writing, 400 raffle tickets remain, so if you want to own a landmark Corvette, get your credit card out. We’ll check back in when Chevy builds its 2 millionth Corvette.

Via, Road&Track


First 2020 Corvette Convertible Arrives at Chevy Dealers


KISS Guitarist Paul Stanley Loves His C8 Corvette Stingray

With its exotics looks, mid-engine layout and near 500 horsepower V8 engine, the C8 Corvette Stingray was always going to be a car that attracted rock stars, professional athletes and actors and actresses as owners.

Among the celebrity owners of the new C8 Corvette is KISS  rhythm guitarist and co-lead vocalist Paul Stanley. In a post shared with his Facebook fans this week, Stanley had the following to say about his new mid-engine ‘Vette:

“For years the auto industry said “Buy American” (and) I said ‘when you manufacture world-class cars I’ll buy them.’ For me the 2020 Corvette C8 is beyond that. It raises the bar with cutting edge technology. It’s a machine I’m proud to drive AND it’s drop dead GORGEOUS. I LOVE mine!”

Stanley’s C8 Corvette appears to be a Summit White model with the Morello Red interior upholstery and black 5-spoke trident wheels. He also appears to have equipped the ‘Vette with the available Bright Red brake calipers and Carbon Flash painted mirrors but opted against the Z51 performance package, judging by the lack of the lower front splitter.

While Stanley indicates that he has avoided owning American cars in the recent past, this isn’t the first time his name has been associated with the iconic Chevrolet Corvette. Back in 2014, Stanley worked with Chevrolet Accessories to develop the 2015 Corvette Stingray Paul Stanley Concept, which featured candy red exterior paint, a silver painted roof, a silver grille insert, quilted parchment leather seats and more. At the time, Stanley said the C7 Corvette was“undeniable in terms of its aesthetics,” and “a world-class piece of machinery.”

Paul Stanley Edition Corvette

At the time, Chevy’s vice president for performance vehicles and motorsports, Jim Campbell, said Stanley’s passion for cars made him an easy fit for the 2014 collaboration.

“It was great working with Paul Stanley, because of his vision and passion for design and automobiles,” Campbell said.

So there you have it, not only is Paul Stanley a fan of the C8 Corvette – he liked the sports car so much he decided to put one in his garage. 

Source: SAM MCEACHERN


2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500

2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500


We’ve been expecting to hear this news and finally today it has been confirmed by Chevrolet that the new 2020 Corvette Stingray will be the official Pace Car of the 104th Indianapolis 500. This marks the 17th race that Corvette has served as the official Pace Car, and the 31st Chevrolet to lead the field.

This year’s running of the Indy 500 will take place on Sunday, August 23 with the race being shown live on NBC.

With no fans allowed in attendance this year due to the COVID-19 pandemic, the official pace car driver will be GM President Mark Reuss.

2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500


“It’s truly an honor to have the opportunity to be behind the wheel of the mid-engine Corvette Pace Car at such a historic race as the Indy 500,” said GM President Mark Reuss. “The 2020 Corvette Stingray is the result of a close collaboration between the Corvette Racing and production engineering teams, setting a new benchmark for supercars around the world.”


The 2020 Corvette Stingray Pace Car is Torch Red and features the high Wing Spoiler and ground effects package. The Z51 Coupe will also wear the 104th Indy 500 livery on the doors. The new 2020 Stingray is capable of accelerating from 0-60 in 2.9 seconds and has a top speed of 194 mph, so it should have no trouble in setting the pace for the IndyCar racers.

2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500


“This is a continuation of our outstanding partnership with Chevrolet,” Indianapolis Motor Speedway President J. Douglas Boles said. “We’re so grateful for all that Chevrolet has contributed to the success of our events. The Torch Red 2020 Corvette Stingray is a world-class machine rich with speed, performance and excitement, perfectly suited to pace the ‘500′ field.”

Chevrolet has been linked to the Indianapolis Motor Speedway with both entities founded in 1911. Company founder and namesake Louis Chevrolet and his brothers Arthur and Gaston raced in the early 500-mile races with Gaston winning the race in 1920. Today, Louis Chevrolet rests in peace in a local Indianapolis cemetery just 15 minutes away from the track.

2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500
2020 Corvette Stingray is the Official Pace Car of the 104th Indianapolis 500

Update

This afternoon we came across this Facebook post from Corvette Exterior Design Manager Kirk Bennion sharing these words from fellow GM designer Adam Barry who led the project. The 2020 Corvette Pace Car features a number of items from Genuine Corvette Accessories as discussed:

2020 Corvette Indy 500 Pace Car


Source:
Indianapolis Motor Speedway


2021 Corvette Pricing Released with Z51 and the E60 Front Lift Seeing Increases

2021 Corvette Pricing Released with Z51 and the E60 Front Lift Seeing Increases

Expected this week from the Corvette Team is the 2021 Corvette pricing schedule and its now available to dealers. A copy was leaked to the internet and now we can see exactly where GM will be raising prices of select 2020 options as well as setting the price for new options for the 2021 model year.

The Corvette Team made a promise back at the Virtual NCM Bash that base pricing would not change from the 2020 model year. That commitment includes the 1LT, 2LT, and 3LT pricing for the Stingray Coupe and Convertible. Those prices are unchanged* and are:

  • $58,900 – 1LT Coupe
  • $66,200 – 2LT Coupe
  • $70,850 – 3LT Coupe
  • $66,400 – 1LT Convertible
  • $73,200 – 2LT Convertible
  • $77,850 – 3LT Convertible

*Prices do not contain the mandatory destination fee of $1,095.

However, we did guess correctly that certain options would most likely be raised for the 2021 model year. These are the returning options from 2020 with the new 2021 Pricing. I have also included the 2020 pricing in parenthesis. The most popular options receiving a price increase are the Z51 Performance Package and the E60 Front Lift:

  • Z51 – Z51 Performance Package $5,995 ($5,000)
  • E60 – Front Lift $1,995 ($1,495)
  • 5DF – Black Trident Spoke Wheels $2,895 ($2,695)
  • 5JR – Carbon Fiber Mirror Covers $1,245 ($1,145)
  • RCC – Engine Cover in Red $525 ($495)
  • RCD – Engine Cover in Sterling Silver $595 ($495)
  • RIA – All weather Floor Liners $205 ($195)
  • CAV – Contoured Cargo Area Liners $145 ($135)

Based on 2020 Sales Data the Corvette Team released during the Virtual NCM Bash in late May, the Z51 Performance Package was ordered by 74% of buyers while the E60 Front Lift accounted for 58% of all Corvettes sold. The LPO Black Trident Spoke Wheels were only ordered by 14% of buyers.

Now for the options new to 2021, Red Mist Metallic Tintcoat is priced at $995, the same as the outgoing Long Beach Red, and the FE2 Magnetic Ride Control without Z51 will cost you $1,895. Silver Flare is the other new exterior color for 2021, but there is no additional cost to select it so it is not listed below.

  • GPH – Red Mist Metallic Tintcoat $995
  • FE2 – Magnetic Ride Control w/o Z51 $1,895
  • DSY – Orange Full Length Racing Stripes $995
  • DSZ – Red Full Length Racing Stripes $995
  • DTO – Yellow Full Length Racing Stripes $995
  • DUH – Blue Full Length Racing Stripes $995
  • DZU – Carbon Flash/Edge Yellow Stinger Graphic $500
  • DZV – Carbon Flash/Midnight Silver Stinger Graphic $500
  • DZX – Carbon Flash/Edge Red Stinger Graphic $500
  • SFE – Wheel Locks $95
  • SQU – High Security Silver Painted Wheel Locks $105
  • W2D – Cargo Net Set $110
  • WKR – C8R Indoor Car Cover $1,195
  • PDY – Roadside Safety Package $175

We note that some of the most popular add-ons were not listed as a 2021 pricing, that being the High Wing or the three-piece Aero Kits which were discontinued and stripped from 2020 orders. We were hoping to see those again. I am also surprised to see that the NPP Performance Exhaust pricing stayed at $1,195 which is what that price as been since it was first introduced on the 2014 Corvettes. Kudos to GM for keeping that popular option from rising as well.

As we’ve discussed, ordering for the 2021 Coupes and Convertibles starts at the end of the week and it will be a busy time for dealers so make sure you have your plans together when you sit down to spec out your Corvette order. Production of the 2021 Corvettes is expected to start in November.


Source:
Chevrolet.com


Corvette hopeful for Road America, expects BMW fightback

Corvette Racing’s Antonio Garcia and Jordan Taylor are optimistic that a C8.R can score the new car’s third consecutive IMSA WeatherTech SportsCar Championship win at Road America this weekend, but they expect a stronger challenge from BMW following the latest Balance of Performance changes.

For this fourth round of the championship, all GT Le Mans-class cars have had their fuel capacity increased – the BMW M8s by 12 liters, the Corvettes by five liters and the Porsche 911 RSRs by three liters – but the BMWs, run by Rahal Letterman Lanigan, have also had their minimum weight cut by 22lbs [10kg] and their power increased by 14hp.

This could throw a high hurdle in the way of Corvette Racing’s hopes to score three IMSA wins on the bounce for the first time since the spring of 2017. Garcia and Taylor won the second round of this season, the Daytona 240, while they finished just behind their victorious teammates Tommy Milner and Oliver Gavin two weeks ago in the Cadillac Grand Prix at Sebring.

Looking ahead to this weekend’s 2hr40min race around the undulating 4.014-mile course at Elkhart Lake, WI, Garcia said: “Tire degradation is always a key thing at Road America. This new Corvette should be a little bit better on that compared to the[2014-’19 predecessor] C7.R.

“Porsche was strong last year and they obviously are going to be strong again. At Sebring, they showed really good pace behind us. With BMW getting a break, it will be difficult to fight them.

“That will create different speeds at different parts of the track where each car will be strong. We will see where everything lines up, but for sure that should be interesting.”

Added Taylor: “Road America is definitely a power track, so I think [BMW’s BoP break] will be pretty major when we go there. We saw at the Rolex [24 Hours] that they had a pretty big power advantage where they were able to drive around most competitors.

“I’m not sure where their loss of performance was at the Daytona and Sebring sprint races compared to the Rolex but going to Road America that change should benefit them.”

The former IMSA Prototype champion concurred with his co-driver regarding tire life, pointing out, “Road America often has a big tire degradation part to it, so for us that could be a big part of the race strategy-wise.”

Explaining Corvette’s ‘hot streak’ with the new-for-2020 mid-engined C8.R since the restart of the IMSA season, Garcia stated: “At the Rolex 24 [in January] we were good but that was hidden by little mistakes and issues we had toward the finish. We had been competitive for the first 20 hours but had a few little things going on with the car because it was very new. The pace was there but we weren’t able to fight for the win at the end.

“Each month, there is a ton of development and we continue to show that. Even when we weren’t on the track, we continued to develop the C8.R.”

Taylor added: “It’s amazing that we’ve come out so strong after the quarantine period… It shows a lot for what Corvette Racing is about and the preparation it does behind the scenes. Even though no one could go to the race shop, the engineers were working from home and made huge strides on the C8.R. We went back to Daytona and obviously had a good race there with the win and then went back to Sebring where we were able to do a two-day test there before the quarantine and one simulator test when that period opened back up.

“For us it was an unknown for us because it was the first non-Daytona track where we were competing against all the other teams. Daytona is so unique in that you can stack up well at that track and have that not be relevant anywhere else. So it was promising that we were able to get the pole. The car was amazing all race weekend, and I think we’ve shown we can be competitive on all different kinds of tracks. I’m really looking for this one at Road America.”

David Malsher-Lopez for Motorsport


Composites-intensive masterwork: 2020 Corvette, Part 2

Appears in Print as: ‘Part 2: Beauty, speed, luxury — 2020 Corvette ‘

composites intensive Corvette 2020 design

Earlier this year, the first installment of eighth-generation Chevrolet Corvette sports cars (C8s) from General Motors Co. (GM, Detroit, Mich., U.S.) came rolling off GM’s Bowling Green, Ky., U.S. assembly line.  Described as the “fastest, most powerful entry Corvette” in the model’s 67-year history, it’s also the most composites-intensive Corvette, and the first to feature a mid-engine configuration. Not only is the 2020 Corvette Stingray beautiful and fast, but it’s tricked out with a host of luxury features. However, don’t let good looks and fast track times fool you: there’s plenty of composites innovation on this car. CW’s two-part coverage of composites use in this vehicle began in the July 2020 issue. This is part 2.

Body structure: part B

The new Corvette features not one but two trunks that, combined, hold 12.6 cubic-feet/0.36 cubic meters of cargo. Both trunks are produced in 42 wt-% chopped fiberglass/vinyl ester-unsaturated polyester (VE-UP) resin, but use different processes driven by geometry and mechanical requirements. The front trunk (frunk) is compression molded 0.95-specific gravity (SG) “float” sheet molding compound (SMC), while the rear trunk is formed via the proprietary PRiME (Prepositioned Reinforcement ensuring Manufacturing Excellence) process, a liquid compression molding (LCM) variant. The float SMC and the PRiME process were developed by processor Molded Fiber Glass Co. (MFG, Ashtabula, Ohio, U.S.). MFG produced all structural SMC and LCM’d parts on the car.

“Although both spaces are characterized by shallow-draft, long-draw walls, the frunk is smaller than the rear trunk, and could be compression molded,” explains Chris Basela, Corvette body structure lead engineer. “The rear trunk needed higher mechanical performance and was a tough geometry to fill with an SMC charge. Because the PRiME process lets us change fiber length, we could use longer pre-positioned reinforcement in our preform. Flowing the resin [not the glass] proved the best approach.”

Ductwork in the Corvette Stingray
Depicted air pathways through the body-structure

The 2020 Corvette is the first car to use body-structure cavities (integral to the body frame) for air-induction ductwork (above), which is fed by multiple primary cooling paths (below). The car’s naturally aspirated V8 engine needs a lot of air, so it was important to ensure good, unimpeded airflow to keep the engine cool. Source (both images) | General Motors Co.

Clever engineering and a new material were key to cooling the C8’s engine. Multiple primary cooling paths (rear inlets behind each door, front wheelhouse vents, and outboard cooling inlets) feed highly complex induction ducts that funnel air through the vehicle and across the engine, before ejection through aluminum-mesh vents and SMC appliqués on either side of the glass partition that showcases the Corvette engine. The appliqués are made with MFG’s float (0.95-SG) SMC (chopped glass/UP-VE resin). Low in volatile-organic compounds (VOCs), the material reduces emissions and eliminates the need for resonators on rear-induction ducts, while reducing cost and mass (2.4 kilograms) versus alternative technologies.

The massive, customer-visible rear surround frame — 64 by 69 by 24 inches (163 by 175 by 61 centimeters) — that surrounds the rear-half of the passenger compartment is compression molded in toughened 1.2-SG SMC. This hybrid-reinforced material features carbon fiber at 15% fiber-volume fraction (FVF) and glass fiber at 30% FVF, with a low-VOC UP resin, formulated to withstand engine-bay heat. The frame forms the dimensional foundation for all rear exterior and interior panels, yet flexible design enables it to be used for multiple model variants. Thanks to significant parts consolidation, secondary attachments were eliminated, increasing interior package space, reducing noise/vibration/harshness (NVH), providing better body structure and sealing performance, improving rear-hatch visibility and reducing mass (15%) and cost versus the outgoing frame. “Given the size of this part, which is almost 6 by 6 feet tall and 2 feet deep, we actually had to make the material flow uphill in the mold, so we were all a little worried on that first shot,” Basela recalls.

Corvette rear surround frame.

The very-large, customer-visible rear surround frame provides the dimensional foundation for all rear exterior and interior panels. Each half of the mold in which the part is formed weighs ~35,000 pounds/15,900 kilograms and was produced by Century Tool, a division of Tooling Tech Group (Fenton, Mich., U.S.). The compression press itself has 2,800 tonnes clamping pressure and a platen that measures 108 by 68 inches (274 by 173 centimeters). Despite its size, cycle time is

a nominal 3 minutes. | SPE Automotive Div.

Equally interesting is the bulkhead (mid-window frame), which was custom-formulated by MFG to resolve high heat and noise challenges, since this portion of the cabin sits directly over the V8 engine. Fiberglass reinforcement combined with beryllium graphite filler in low-VOC VE-UP resin deadens sound transmission into the passenger compartment so effectively that it eliminated the need for secondary sound-deadening countermeasures. That, in turn, reduced costs, increased interior package space and passenger comfort, and improved body sealing and NVH. “With a specific gravity of 2.2, this is the first composite part I’ve ever been asked to add mass to rather than take it out,” laughs Basela.

Closures and trim

Exterior body panels are all bonded (inner/outer), painted, toughened 1.2-SG SMC (22-28% FVF fiberglass/UP resin, depending on component) from Continental Structural Plastics (CSP), a Teijin Group company (Auburn Hills, Mich., U.S.). By bolting on composite closures, GM achieves the C8’s aggressive styling, aerodynamics and functional cooling integration, with  cost-effective lightweighting on multiple model variants using common parts. All body panels are painted inline on a “skuk system” in vehicle position, using Bowling Green’s innovative robotic wet-sanding process.

High-temp FIP silicone gasket on rear service doors

Rear service doors are molded from toughened SMC and feature a high-temperature, foam-in-place silicone gasket that provides a durable seal with excellent compression-set resistance while handling long-term exposure to engine-bay heat. Another composite — heat- and abrasion-resistant aluminized aramid fabric — is used as a heat shield to provide extra thermal protection on door interiors. | SPE Automotive Div.

Another innovation involves use of a one-part, thixotropic silicone elastomeric foam gasket applied to the back side of SMC service doors, which are located in the rear trunk (one on coupés, two on convertibles), and permit customer access to the air-filter system. Owing to proximity to the engine bay, the high-performance foam-in-place

 

(FIP) elastomer (Silastic 3-8186 from Dow, Inc., Midland, Mich., U.S.) was specified to survive continuous-use temperatures up to 392°F/200°C while providing a durable seal with excellent compression-set resistance, even after repeated open/close cycles. GM reports that most other die-cut foams and gaskets would either have melted or broken down under continuous exposure to such temperatures. After dispensing, the applied gasket is heat-treated at 167°F/75°C for 10 minutes to expand the foam, eliminating die-cutting cost and waste. The doors themselves are toughened SMC (42% FVF glass in a VE-UP matrix). Heat shields, produced by Gentex Corp. (Carbondale, Pa., U.S.) using heat- and abrasion-resistant aluminized Kevlar aramid fabrics (fiber from DuPont de Nemours, Inc., Wilmington, Del., U.S.), provide door interiors with extra thermal protection.

 

The new mid-engine 2020 Chevrolet Corvette Stingray from General Motors Co. is said to be the fastest, most powerful entry-level Corvette in the model’s 67-year history. It’s also the most composites-intensive, with a host of innovative technology. | General Motors Co.

GM also used its second-generation, fully automated precision wheel-balance system on the C8. Developed with The 3M Co. (St. Paul, Minn., U.S.) and ESYS Automation (Auburn Hills, Mich., U.S.), the high-density (5.8-SG) composite wheel weights with tailored magnetic properties replaced traditional stamped metallic weights in painted steel, zinc or lead that have specific mass and must be hand-applied to wheels.

The new system uses large spools of extruded tape with adhesive backing that contain 67% by volume post-industrial, corrosion-resistant, fully recyclable steel alloy in a fluoropolymer base. The automated system examines each wheel, then cuts and applies custom-weight tape segments in smaller, more precise increments to improve ride and reduce tire wear. It also reduces assembly time and cost, simplifies inventory, eliminates scrap and labor and is offered in more colors than metal weights.

Coupé roofs are available in three trim levels:  painted, low-density toughened SMC (from CSP); clear, hard-coated polycarbonate (PC); and clear-coated/exposed-weave carbon fiber composite with painted edges (from deBotech Inc., Mooresville, N.C.). CSP also supplies several Class A, toughened 1.2-SG SMC panels for convertible-model retractable-roof systems.

Additional Corvette beauty shots. 

Additional Corvette beauty shots. Source | General Motors Co.

Other exterior trim panels include painted thermoplastic polyolefin (TPO) front fascia upper and lower, the latter with integrated ducts to direct air to brakes (Z51 package only) and outboard heat exchangers. Outer grille and brake cooling vents are painted acrylonitrile butadiene styrene (ABS).

The upper rear fascia is molded-in-color (MIC) TPO, but the lower rear fascia assembly is Class A painted, 1.2-SG SMC (glass/UP resin), owing to the part’s close proximity to hot exhaust tips. SMC’s excellent mechanical performance enabled GM to design an unsupported short rear overhang and use larger spacings between attachments without sagging. SMC also spreads loads efficiently over a larger area during low-speed rear crashes than thermoplastics. Brackets and rear parking-assist sensors are bonded to the SMC. This is said to be the first time SMC bumper fascias have been used on high-volume vehicles.

Rear-hatch appliqués feature painted PC/ABS for the upper panel, SMC with aluminum mesh for side vents and an SMC lower appliqué to accommodate thermal loading directly over the engine. These SMC panels are produced by LyondellBasell’s Quantum Composites Inc. (Bay City, Mich., U.S.). Door-handle release switches are PC/ABS, while the rear air-intake vent is SMC. The base car sports a blowmolded, painted ABS spoiler and the rear air-exit grille is injection molded painted ABS. A-pillar and header appliqués are painted ABS, as are exterior side-view mirror caps and radiator inlet grilles. Depending on the option package, a toughened SMC front underwing and either a blowmolded TPO or carbon fiber composite front splitter/diffuser — clear-coated/visible-weave carbon/epoxy produced by deBotech using prepreg from Solvay Composite Materials (Alpharetta, Ga., U.S.) — contribute additional aerodynamic stability. A rear diffuser in toughened SMC mates to the SMC lower rear fascia in Class A painted SMC from MFG.

The premium carbon fiber trim package features various clear-coated/visible weave carbon fiber accents inside and out, including mirror caps, front grille insert, front splitter, accessory wing, engine-compartment covers, interior door switch plates, rocker moldings, instrument-panel cluster bezel, door-handle covers, quarter appliqués and ride-control plate. These components are produced by deBotech, SMI Composites LLC (Comer, Ga., U.S.) and Plasan Carbon Composites (Wixom, Mich., U.S.).

Chevrolet Corvette Stingray

The Corvette is not only fast and beautiful but contains a host of creature comforts. For composites aficionados, the premium carbon-trim upgrade adds numerous clear-coated/visible-weave carbon fiber composite accents to exterior and interior surfaces, such as the ride-control plate shown here. | General Motors Co.

Advancing technology

The 2020 Corvette has already won many prestigious industry awards, including 2020 MotorTrend Car of the Year, 2020 Automotive News PACE (Premier Automotive supplier Contributions to Excellence) Partnership Award, and several awards from the Society of Plastics Engineers (SPE), including 2019 Vehicle Engineering Team Award. “Although the new Stingray’s mid-engine architecture has dominated headlines, no matter where the engine is — in front of or behind the driver — for eight generations, Corvettes have always advanced the state of the art in automotive materials technology,” adds Tadge Juechter, executive chief engineer-Global Corvette. “Advancing technology is at the heart of what we do.”


Legally Blind for 44 Years, a Canadian Man Has Sight Restored and Buys a Corvette

Legally Blind for 44 Years, a Canadian Man Has Sight Restored and Buys a Corvette

Seeing, quite literally, is believing for a Canadian man named Mike Schickerowski.

At age 44, he got his driver’s license just two weeks ago.

Why the delay?

Schickerowski was born with a disorder called nystagmus, which causes the brain to see images as a blur.

“My brain would never interpret the image as a steady picture,” he explained. “It basically involves involuntary movement of your eyes. If you’ve ever taken a photo with your camera and moved it slightly or the object moved and it’s a blur, it’s the exact same symptoms.”

That means Schikerowski has been legally blind his entire life, that is, until undergoing successful experimental surgery to correct the condition in California in October 2018.

He says being able to see has changed his life in many ways, most notably allowing him to take part in the simple things of life.

“I took my son fishing last week,” he said. “I was never able to do that before on my own. I took my daughter for ice cream. It’s unbelievable.”

Of course, those trips are made even more special because Schickerowski decided to splurge on his first vehicle ever – a yellow C7 Corvette Grand Sport. So confident he would pass the driver’s license exam for the first time, he purchased the flashy sports care before he even passed the test! “it was overwhelming to think I was doing it at that age,” he said, “but I did pretty well and I just couldn’t believe it.”

While some people thought he should have bought a more practical vehicle, especially living in the province of Alberta, Schickerowski says he wanted to stand out.

“Some people said, ‘Oh, it’s Alberta, you need a truck,’ and sure I like trucks — they’re nice — but everybody’s got a truck,” he said.

TITLE


Schickerowski is grateful that he is able to drive the Corvette on his own, but he was even more excited about being able to see the world clearly for the first time after the surgery was a success.

“It was beautiful to see,” he said, “but it was more the realization of what I missed my whole life. It was emotional breakdown. My mom was bawling, and my wife was ecstatic. It was never supposed to happen.”

While he says there was a “sad moment” realizing how much of his life had already gone by and “how much I had suffered,” he says he’s “still excited for the future.”

His wife, Angie, says watching Mike see things in 3D for the first time was “unbelievable – things like fireworks, there’s all these things.”

“I’ve lived a wonderful life and enjoyed every moment,” he says. “This is just the awakening to possibilities of the future and the opportunities that are there.”

Add his yellow Corvette to that list of expanding opportunities, and here’s hoping he enjoys his car for years to come.


Thanks to Bob S. for the link!


Source:
globalnews.ca


Success Rate “Speaks Volumes” for New Corvette C8.R

Corvette Racing carries momentum to collect 101st victory in IMSA competition…

Photo: Corvette Racing

Corvette Racing’s second win in only the third IMSA WeatherTech SportsCar Championship race this season “speaks volumes” for the new Chevrolet Corvette C8.R according to Jordan Taylor.

The No. 4 entry of Tommy Milner and Oliver Gavin led home a 1-2 finish for Corvette at the Cadillac Grand Prix of Sebring, marking the team’s first sweep since Lime Rock Park in 2016.

It gave the Pratt & Miller-run factory GT Le Mans squad its 101st victory in IMSA competition after notching up the century last time out at Daytona.

Image

Milner led home the sister car of Antonio Garcia by less than five-tenths of a second but says the final laps were not as easy as it looked.

“I know it took us a while to get to 100 but it’s nice to get over the hump and get 101 so you’re not talking about that one,” he said.

“Today was all about strategy, all about not making mistakes. It looked like we were going to have a pretty good race there with the Porsche. It was all pretty close but then it fell apart as far as that goes.

“In the end, it was just left to myself and Antonio and Olly and Jordan there to put on a show a little bit there.

“Olly really made the race for us there saving fuel and that allowed us to have a bit of a better pit stop and get out in front of the No. 3 car and that was the race for us.

“It got pretty close there at the end, he was close but he was a little bit nicer to me than he could have been.”

Image

Co-driver of the second-placed No. 3 Corvette, Taylor, was pleased with the team’s double podium.

“It’s a great day for Corvette Racing,” he said. “It’s our third race and to get two wins, our first 1-2 since 2016, I think it speaks volumes for the team and this new C8.R.”

Porsche Incident Spoiled Potentially Close GTLM Race

While Corvette’s run was without trouble, the same could not be said for the factory Porsche 911 RSR-19s, with both the Nos. 911 and 912 car’s chances of victory being dashed in seconds.

The pair came together in the first round of pit stops which resulted in the No. 912 losing its nose and the No. 911 suffering a puncture from the contact a few laps later.

Laurens Vanthoor and Earl Bamber impressively recovered to third in the No. 912 Porsche. However, Milner believes the race would have been closer had the Porsches not collided.

Image

“It was looking like it was going to be very close pace-wise and everything,” he said.

“You saw in the pit stop as well we came in together and we were going to leave together. In terms of strategy details, it looked like it was going to be a close race, fuel numbers, tires whatever it was.

“They’ve been fast all season and continue to be quite quick so for sure we have some work to do to find an advantage somewhere if we can and ultimately not make mistakes throughout the race.

“We saw today how one little mistake can ruin your race. We just need to be extra vigilant, no pit lane incidents like that. All those little details that aren’t quite sexy in some way but make the race for you in the end.”

Image

Gavin was on pit road in the fast lane and was caught up in the incident but did not sustain any damage.

“I didn’t know anything about it. I just saw one of the Porsches left missing its front bumper,” he said. “I think it was all of us trying to leave together and there just wasn’t enough room.

“I was already in the lane so when it’s like that I have priority.”

Slade Perrins for Sportscar 365


Chevy Teaser Video Hints At Something Colorful For The 2021 Corvette

The Gulf livery’s iconic colors make an appearance.

We’re quickly approaching the first anniversary of Chevy’s introduction of the 2020 Corvette C8, which happened on July 18. Now, less than two weeks ahead of that date, the Chevy Corvette’s official Facebook page shared a short, 14-second teaser video that hints at something new for the Corvette for the 2021 model year.

The post says, “It’s time to earn some new racing stripes,” while the quick-hitting teaser hints at what Chevy is “Adding to the [Corvette’s] legacy.” However, we have no idea what that means exactly. The teaser shows off some stylized Corvette footage with colored stripes crisscrossing the video. There are also four overhead shots of striped Corvettes that flash on the screen. Two are black, one with a pair of red stripes while the other has yellow ones. There’s a blue-on-white one, and another that mimics the iconic blue-and-orange Gulf livery.

For as much fanfare as the 2020 Corvette created, the Stingray model the automaker introduced was just the beginning. We expect Chevy to add more high-performance models to the Corvette lineup, like the Z06. But we don’t think Chevy is ready to reveal that top-tier model just yet. Instead, we’d bet that Chevy is planning to introduce a new appearance package, or packages, that help enhance the car’s appearance. It could be similar to the Competition Sport package Chevy introduced for the 2009 Corvette C6.

We know for sure that Chevy still has a ton of Corvette excitement to reveal going forward. Fans are eagerly awaiting the next Z06, and the numerous spy photos and videos don’t help. We know it should pack a 5.5-liter flat-plane crank V8 that’ll leapfrog the Stingray in power, performance, and price. We don’t expect that model to arrive until the 2022 model year, so until then, we can look forward to Chevy’s latest, which the automaker should reveal soon.

Source: Chevrolet Corvette / Facebook


GM reveals price, features of 2021 Corvette Stingray, including two new colors

General Motors said Wednesday it will keep the price of its 2021 Chevrolet Corvette Stingray the same as the introductory 2020 model.

The 2021 Corvette, which goes on sale late in the fourth quarter, will start at $59,995, matching this year’s model, which is about a $4,000 increase over the 2019 Corvette. Comparatively, the mid-engine Porsche 718 Cayman starts at $61,250. All prices include destination charges.

There will also be some new content in the 2021 model, GM said. 

“Our mission was to develop a new sports car, combining the successful attributes of Corvette with the performance and driving experience of mid-engine supercars,” said Tadge Juechter, Corvette executive chief engineer. “We are thrilled with the enthusiasm the mid-engine Corvette brought following its launch and are keeping it fresh with new content for the 2021 model.” 

2021 Chevrolet Corvette Stingray Coupe and Convertible (far right in new Silver Flare Metallic)

Here is what will be new on the 2021 Corvette:

  • Magnetic Selective Ride Control suspension, which is new for non-Z51 models. 
  • Standard wireless Apple CarPlay/wireless Android auto
  • Red Mist Metallic Tintcoat exterior color
  • Silver Flare Metallic exterior color
  • Sky Cool Gray/Yellow Strike interior color
  • New full-length dual racing stripe package colors: blue, orange, red and yellow
  • Stinger Stripes in three colors: Carbon Flash/Edge Red, Carbon Flash/Edge Yellow and Carbon Flash/Midnight Silver
  • Driver mode on-screen visualization and new track digital tachometer
  • Standard Buckle To Drive, a safety technology that, when active, can prevent the driver from shifting the vehicle out of park if the driver’s seat belt is not buckled for up to 20 seconds

GM will also offer on the next-generation car Chevrolet’s first eight-speed dual-clutch transmission to allow for faster shifting and more power.

Here are some other engine features on the 2021 model:

  • Engine: 6.2-liter LT2 V-8 with direct injection, variable valve timing and active fuel management
  • Transmission: eight-speed dual-clutch with manual and automatic modes
  • Six modes of Driver Mode Selector — Tour, Sport, Track, Weather, and MyMode and Z Mode customizable modes
  • Brakes: four-wheel antilock, four-wheel disc, four-piston calipers (12.6-inch front rotors, 13.3-inch rear rotors)
  • NEW: Available Magnetic Selective Ride Control suspension. It reads the road better, providing more precise data.
  • Available Z51 Performance Package: brakes, suspension, exhaust among other features
  • Z51 Performance with Magnetic Selective Ride Control, includes Performance Traction Management
  • Front lift: adjustable height with memory

Jamie L. LaReau Detroit Free Press


The Corvette Assembly Plant Has 10 Truckloads of 2020 Corvettes Ready to Ship

The Corvette Assembly Plant Has 10 Truckloads of 2020 Corvettes Ready to Ship!
Photo Credit: Jeremy Welborn


A member of the MidEngineCorvetteForum.com is offering even more proof that Corvette production has returned pretty much back to normal by sharing Saturdays shipping manifests of new 2020 Corvette Stingrays headed to dealerships. Each Jack Cooper Transporter can hold a maximum of 10 new C8 Corvettes and so this batch of 10 transports contains just under 100 cars which is nearly identical to one shift’s production totals.

From the printouts we see the VIN sequence numbers range from #805 to #4126 which was just completed last week. The cars are sorted by destination and the trucks will soon be headed to Texas, Oklahoma, Florida, South Carolina, and Maryland. The NCM is receiving two trucks and one load will be headed north to Canada.

2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests
2020 Corvette Shipping Manifests


There are going to be some very happy Corvette owners next week! If one of these is yours, let us know in the comments below!

To find the shipping status of your 2020 Corvette, go to https://www.palsapp.com/, then click on the search icon on the top right of the page (looks like a magnifying glass). Enter your VIN and click the search icon to the right of the input field.


Source:
MidEngineCorvetteForum.com


REPORT: C8 Corvette Ranks 8th on 2020’s Most American Made Cars Index

The mid-engine C8 Corvette’s clean-sheet redesign resulted in just a couple of parts carried over from the C7 generation, but there is enough “baseball and apple pie” in the sports car to keep it in the Top 10 of the 2020 American Made Index as compiled by Cars.com.

Chevrolet landed two vehicles on the 2020 List with the Corvette coming in at a very appropriate 8th place and it was joined by the Colorado that landed in 10th place. They were the only two GM vehicles to make the list.

The American Made Index, or AMI, “is an independent annual list that ranks the new vehicles that contribute most to the U.S. economy based on criteria ranging from U.S. factory jobs and manufacturing plants to parts sourcing.” Manufacturers are required by law to annually report the percentage of US and Canadian parts and that information appears on the window sticker of all new vehicles sold in the USA.

The AMI studied 91 vehicles and the ranking looks at four key factors:

  1. Origins of the engine and transmission
  2. Origin of parts in the car (as reported by the American Automobile Labeling Act)
  3. Final assembly location
  4. U.S. manufacturing workforce relative to production footprint

The were some new additions to the list for 2020 with the Ford Ranger leap-frogging the Jeep Cherokee to #1 while Tesla landed three vehicles on the list.

2020 American Made Index by Cars.com

Cars.com says that 70% of shoppers consider a car’s impact on the US economy a significant or deciding factor in their vehicle choice and the COVID-19 pandemic has increased the desire of Americans to “buy local.” The survey found that nearly 40% of consumers report they are more likely to buy an American-made car due to the current health and economic crisis, while just 4% said they were less likely. A whopping 26% said it was “unpatriotic” to buy a non-American-made car, compared to just 18% in 2019.

“This marks the 15th year we have released the American-Made Index, and for the first time, we are ranking a full, comprehensive list of qualifying American-made cars available in the U.S. Of some 350 cars on the market for 2020, 91 models qualified for our index,” said Kelsey Mays, Cars.com’s senior consumer affairs and vehicle evaluations editor. “The auto industry is highly globalized, but these 91 models bring jobs to America and investments to our local communities — a growing concern for Americans in the current climate.”

You see find reviews of the Top 10 American Made Vehicles at Cars.com as well as view several videos that discuss the 2020 American Made Index.
Source:
Cars.com


Composites-intensive masterwork: 2020 Corvette, Part 1

Eighth-generation vehicle sports more composites, and features parts produced using unique materials and processes.
#weaving #discontinuousfiber #outofautoclave

here and in Part 2 next month.

composites in mid-engine Corvette

here and in Part 2 next month.

New engine configuration changes everything

GM engineering went into preliminary design knowing they’d be working on a mid-engine vehicle — the first production Corvette in eight generations to sport that configuration. “We evolved the front-engine architecture as far as we could for performance, so shifting to a mid-engine design was the next logical step to improve an already great car and be the segment leader,” explains GM’s Tadge Juechter, executive chief engineer-Global Corvette. Equipped with the Z51 performance package, the 2020 Corvette Stingray can accelerate 0-60 mph (0-97 kmh) in 2.9 seconds and reach top speeds of 194 mph (312 kmh). Pushing the engine toward the vehicle’s rear affected many things, including the car’s center of gravity, the relative position of occupants, transmission location and design of underbody panels and trunk storage. The mid-engine design also introduced higher operating temperatures and noise to new areas of the car.

All eight generations of the Chevrolet Corvette

The eighth-generation Chevrolet Corvette — all eight generations (C1-C8) shown above, left to right respectively — from General Motors Co. started production earlier this year. This mid-engine sports car is not only impressively fast, and the most composites-intensive Corvette yet, but it features an array of genuinely innovative composites applications. Source | General Motors Co.

“Because of the mid-engine, we had to do things differently,” explains Ed Moss, Corvette body structure engineering group manager. “From the start, we had so many discussions about how to lay out the body structure. At one point, everything was on the table as we discussed the best way to design and build each system. For example, we debated metallic versus composite for wheelhouses. If we’d kept the C7’s composite wheelhouses, we’d have to bond to the hinge pillar [A pillar], which is immediately adjacent to the front wheel in a mid-engine vehicle, leaving very little package space. We went with metal there. We even briefly discussed metal versus composite body panels. However, it would’ve been economically infeasible to create the C8’s styling lines in metallics.”

“A real challenge we faced was how to handle air induction,” recalls Chris Basela, Corvette body structure lead engineer, explaining the need for a different method to funnel cooling air into and across the naturally aspirated, 495-horsepower, 6.2-liter V8 engine, which generates 470 foot-pounds (637 Newton-meters) of torque. “We tried all kinds of designs that forced air to take really torturous paths, creating eddies and flows we didn’t want. It took lots of iterative work with the powertrain team to develop the best path for airflow because the car needs to breathe freely with no restriction. We also needed access to the air box and had to work around rear trunk space. Another issue was heat and engine noise in the passenger compartment, because occupants no longer sit behind the engine but are positioned directly in front of it. And we were especially conscious of cabin air quality as laws had changed in Europe and elsewhere since the C7, so we worked really hard to reduce VOCs [volatile organic compounds].”

“Even working out how to assemble the car was a challenge,” adds Moss. “With a front-engine design, you have a long hood and large engine compartment, providing operators plenty of room to build the car from inside the compartment, even with the front bumper beam already welded on. On the mid-engine Corvette, with its very short front clip, we keep the front of the car open as the vehicle is built out, then bolt on the front bumper.”

“It was quite a balancing act to get the proper shapes, while ensuring our suppliers could produce the parts and our team in Bowling Green [GM’s Kentucky-based Corvette assembly plant] could assemble them,” continues Basela. “In the end, there was only one carryover composite from the C7’s body to the C8.” This was tough Class A, 1.2 specific gravity (SG) sheet molding compound (SMC) developed for the 2016 Corvette and used in a variety of exterior closures on the new vehicle.

Vehicle architecture

For four generations (C5-C8), Corvettes have featured a three-layer, multi-material body structure: the frame, usually a mix of aluminum or steel — this time with a carbon fiber-reinforced composite (CFRP) part; the body structure, which is largely bonded composite to capitalize on design and manufacturing flexibility; plus bolt-on closeouts (body panels), which have been composite since Covette’s June 1953 debut. This layered hybrid structure not only provides affordable lightweighting in high production volumes — particularly for cars of this performance class — but also permits multiple vehicle variants to be produced at low tooling investment. In fact, for the current C8, GM managed to produce all Class A composite body panels (bonded inners and outers) on both the base model coupé and convertible using just 20 tools.

GM and its suppliers have already won many awards for innovative composites use on the 2020 Corvette Stingray. Among those standing above are key GM engineering team members at last November’s 49th annual Automotive Innovation Awards Gala, where GM won SPE Automotive Div.’s Vehicle Engineering Team Award. A number of composite parts on the vehicle also were finalists or category winners at the event. Source | SPE Automotive  Div.

In addition, Corvettes have always been engineered with an open-roof architecture, regardless of whether they are actually convertibles or coupés with fixed or removable roof panels. Because open-roof vehicles are generally less stiff than those with fixed roofs, an important focus for each Corvette’s engineering is always to create the stiffest foundation possible to improve suspension and steering. Historically, tunnels(housing transmissions and driveshafts on front-engine vehicles) have dominated Corvette body structures and have been key enablers for achieving high torsional rigidity. In the case of the new Corvette, GM achieved even higher rigidity. With the roof removed, the C8 body is 53.78% stiffer than a benchmark high-performance mid-engine competitor, 29.27% stiffer than a second high-performance mid-engine competitor, and 13.79% stiffer than the C7. Two composite parts made important contributions to vehicle stiffness—one directly attached to the frame structure (rear bumper beam) and another attached to the underbody (lower tunnel closeout).

Frame structure

The C8’s frame is largely aluminum alloy with one CFRP part developed to meet GM’s stringent dollar-per-kilogram targets. In contrast, the C7 frame was all-aluminum and the C6 was mostly steel.

The only composite part directly mounted to the frame that travels with the body-in-white (BIW) through the electrophoretic rust-coat process (which GM calls ELPO), is a unique CFRP rear bumper beam. This part helps stiffen the frame and contributes to rear-impact performance. Its curved shape — possible thanks to a novel process called radius pultrusion developed by Thomas GmbH + Co. Technik + Innovation KG (TTI, Bremervörde, Germany) — enables it to match rear styling cues and fit in limited package space while maintaining dimensional integrity close to engine-bay heat. As the auto industry’s first curved pultruded part (see our full feature on this part in the CW May 2020 issue), the hollow, two-chambered beam was produced by Shape Corp. (Grand Haven, Mich., U.S.) on equipment developed and built by TTI. The beam weighs just 1.3 kilograms and features a bonded/bolted tow-hook eye capable of 25 kilonewtons of pull-out force.

An auto industry first, the 2020 Corvette sports a curved rear bumper beam in pultruded carbon fiber composite produced with 87 individual carbon tows and eight carbon fiber non-crimp fabrics (NCFs) impregnated with polyurethane-acrylate resin. The hollow, two-chambered beam is 66% lighter than the outgoing aluminum beam and met GM’s demanding dollar-per-kilogram targets. Source | Shape Corp.

Body Structure: part A

Virtually all of the C8’s body structure components are composite and are bonded and/or bolted to the frame after the latter undergoes ELPO. Notable composite parts at this level include structural underbody closures and the floor — which we’ll cover in this issue — and front and rear trunks, induction ducts and the rear surround and bulkhead — which we’ll cover, along with body panels and trim, next month.

This hybrid-composite, lower-tunnel closeout is produced using a variant of liquid compression molding. It eliminated secondary attachments, lowered mass by 3 kilograms and reduced labor, tooling and capital costs vs. aluminum. Source | SPE Automotive Div.

The removable lower-tunnel structural closeout on the C8, which acts as an access door, contributes more than 10% of the vehicle’s torsional rigidity and acts as a primary load path during a crash. This hybrid-composite panel consists of three layers of glass fiber preform. These consist of continuous/woven and chopped/random fibers at 38% fiber volume fraction (FVF), with veils added to top and bottom face layers on each stack for improved surface finish. Glass preforms are interleaved with two layers of preforms made using Toray (Tokyo, Japan) T700 12K standard-modulus carbon fiber in the form of NCF biaxial fabric at 21% FVF and a vinyl ester (VE) matrix. The closeout is produced by Molded Fiber Glass Co. (MFG, Ashtabula, Ohio, U.S.) using its proprietary PRiME (Prepositioned Reinforcement ensuring Manufacturing Excellence) process, a type of liquid compression molding (LCM).

Aside from a single aluminum closeout near the rear wheels that is part of the engine cradle, the remaining underbody panels consist of either compression molded SMC or injection molded thermoplastics. Among other benefits, these panels reduce underbody turbulence and drag, improve fuel efficiency and keep moisture, dust and stones out of the vehicle’s engine and driveline. Further, they provide the dimensional foundation for multiple exterior and interior interfaces.

The low-density but structural SMC panels feature new formulations (in this case, 40% FVF chopped fiberglass/unsaturated polyester (UP) resin) developed by MFG. The material is called “float” SMC because each panel’s density is less than 1.0 (average SG=0.97) and thus can float in water. MFG produced all structural SMC and LCM’d parts on the car.

An important contributor to vehicle lightweighting on the C8 is the extensive use of “float” SMC. With specific gravity values less than 1.0, this low-density but structural SMC developed by MFG is used in a variety of non-Class A parts, including underbody panels, the dash panel, air-induction ductwork and the front trunk. Source | Molded Fiber Glass Co.

The vehicle also sports a hybrid floor optimized for torsional bending and side-pole impact protection (engaging the rocker panels and tunnel, to which it is joined). Floor panels feature cabin-facing stamped aluminum bonded to sheets of road-facing 1.5-SG composite (60 wt-% continuous and woven glass fiber/VE) produced via the PRiME process. Before heat-bonding both layers with Pliogrip 9100 polyurethane structural adhesive from Ashland Global Holdings Inc. (Wilmington, Del., U.S.), MFG cleans and preps the materials.

All composite parts directly bonded to the C8 frame are first subjected to laser ablation, a process developed by GM, MFG and Adapt Laser Systems LLC (Kansas City, Mo., U.S.) for the 2016 Corvette, and adapted from a composites industry method for mold cleaning. Laser ablation replaces hand sanding and reduces labor, time and cost, eliminates dust and improves repeatability. Laser path, angle of attack and energy level are customizable for each part’s material and geometry. To maximize manufacturing flexibility, the entire underbody, including the floor, is connected to the frame and itself via bonding and screws.

In the August issue of CW, we’ll continue covering composites innovation on the new Corvette, resuming with additional components at the body structures level and finishing with exterior closures (body panels), plus additional trim and upgrades.

Peggy Malnati for Composites World


Watch A Corvette C8 Hunt Down A Dodge Viper ACR

It seems comfortable at the limit.

The C8 Corvette is Chevrolet’s first stab at building a true mid-engine supercar. While much faster versions will follow, the C8 Stingray in base form can hold its own against more exotic and more powerful machinery. We recently wrote about a C8 Stingray demolishing the quarter-mile, but now we shift our focus to the Laguna Seca Raceway, where a C8 goes up against one of the meanest American performance cars out there: the Dodge Viper ACR.

The C8 is clearly at home on a track as we can see in the video. This Torch Red Corvette gets pushed to its limits and comes out as an unexpected hero.

The 2020 C8 Chevrolet Corvette is no wimp when it comes to numbers: powered by a naturally aspirated 6.2-liter V8, this car produces 490 horsepower and 470 lb-ft of torque. That’s enough to launch it to sixty in only 2.9 seconds when fitted with the Z51 package. This translates into a car that is deceptively fast, especially when compared to big dogs such as the Viper ACR.

In the video, we can see the Vette slowly warming up to the track conditions, with that naturally-aspirated engine filling the cabin with the best noise you could imagine. It is clear that the driver is trying to find his comfort zone.

Side View
Top View
Engine Bay
Exhaust

After a short sprint, the driver and car seem to be clicking, and the pace increases. In the distance, you can see some cars getting closer and closer: it turns out that it’s a Porsche 911 GT3. The action starts at around the 3:15 mark, but you’ll have to wait until the 6:40 mark to see the battle between the Viper and C8.

We have no doubt that in the hands of an experienced driver the Viper would be the faster car, but getting the most out of the downforce capability of this car takes a serious driver and it’ss clear to see that the C8 Corvette is an easier car to drive at the limit. If this is what the Stingray is capable of, we can’t wait to see what faster versions will do.

Michael Butler for CarBuzz


Time Is Running Out To Buy A 2019 Chevrolet Corvette C7

With demand for the C8 outstripping supply, it’s a great time to buy a nearly new C7.

Last year saw the introduction of a mid-engined Chevrolet Corvette Stingray for the first time when the C8 took over from the front-engined C7. It marked a major departure for any Corvette, but thankfully, the C8 has retained the unmatched bang-for-buck performance and power that made the C7 so impressive.

For customers who still want to purchase a 2019 C7, time is running out. According to a report by Corvette Forum, there are now fewer than 300 examples of the 2019 C7 for sale in the country. That said, it may still be easier to get hold of one than the 2020 C8, of which only a few are on sale at dramatically marked-up prices.

2014-2019 Chevrolet Corvette Stingray Coupe Front View Driving

2014-2019 Chevrolet Corvette Stingray Coupe Front Angle View
2014-2019 Chevrolet Corvette Stingray Coupe Rear Angle View

As of June 4, there were 289 C7s listed for sale based on information from a Chevy dealership in Pennsylvania. With zero-percent APR financing over 72 months along with a rebate of $3,250, the incentives are attractive and in stark contrast to the 2020 C8s, with many examples of the new car selling for over $100,000.

The 2019 C7 inventory includes 62 Z06s, 44 of the Z51 variants, and just four examples of the crazy ZR1. Of course, the latter was the ultimate C7 with its 755-horsepower supercharged V8 engine sending it to 60 mph in less than three seconds. State availability of C7s varies significantly, with 28 models in New Hampshire and 22 in Illinois, but nothing at all in Kansas, Maine, Alaska, and South Dakota.Most Extreme Brabus Creations EverMcLaren Special Operations Finest Creations

2014-2019 Chevrolet Corvette Stingray Coupe Front Angle View
2014-2019 Chevrolet Corvette Stingray Coupe Rear View
2014-2019 Chevrolet Corvette Stingray Coupe Steering Wheel Controls

With the current sky-high demand for the C8, purchasing a nearly new C7 could be the perfect solution until the C8 increases in availability. Plus, you’ll save a lot of money. Around three weeks ago, car rental company Hertz was selling 100th Anniversary Editions of the C7 (based on the Z06) for as little as $57,000. Although that’s close to the base C8’s starting price, it’s just about impossible to find a C8 in this spec at the moment.

Besides, whether the engine is midship or in front, the Corvette offers as much driving enjoyment at the price as anything else out there. The new C8 may have moved the game on, but the C7 is far from disgraced and remains a cracking sports car.

2019 Chevrolet Corvette ZR1 Coupe Front Angle View
2019 Chevrolet Corvette ZR1 Coupe Hood
2019 Chevrolet Corvette ZR1 Coupe Front Seats
2019 Chevrolet Corvette ZR1 Coupe Badge

Karl Furlong for Carbuzz


2020 C8 Corvette Production Rolling Without Incident

With constrained production, these cars are instant modern collectibles.


General Motors has a lot of orders to fulfill for the 2020 C8 Corvette and the Corvette Assembly plant in Bowling Green, Kentucky is finally getting back to production. Originally, the factory was idled and employees furloughed back on March 20, a move that GM painted as lasting for only two weeks. Here we are a little over two months later with few C8 Corvettes made, guaranteeing the 2020 model year is an instant collectible due to small production numbers.

2020 C8 Corvette Production Rolling Without Incident

The so-called “COVID Corvettes” are about to increase in number, but don’t expect anything dramatic. This week only 550 of the 1,200 workers for the Corvette Assembly plant have returned to the production line.

Those workers are having to wear protective equipment like masks and deal with revised procedures designed to maximize sanitary conditions on the assembly line. However, all those changes will slow the production process down significantly.

2020 C8 Corvette Production Rolling Without Incident

On top of that, reports claim at least 230 C8 current builds were set aside unfinished when the factory was idled. Each car was wrapped tightly in plastic to avoid dust and other debris, so that must be removed, the Corvettes moved to their appropriate places in the production line, and the assembly process finished for each one. Some are speculating this could take several weeks.

Thanks to many suppliers for Corvette Assembly having closed as well, there aren’t enough parts to bring on the rest of the assembly line workers. Those who are going to work have been selected by seniority. They must answer a series of questions about coronavirus symptoms before entering the factory floor. In addition, each worker’s temperature is taken.

2020 C8 Corvette Production Rolling Without Incident

GM hasn’t provided any official word on how many 2020 Chevrolet Corvettes will be made. Unofficial estimates peg it at a small fraction of the normal production levels, meaning many who ordered a C8 will have to wait until 2021 to get one. The lucky few who do get a 2020 model are sitting on a rare COVID Corvette that’s a part of history at this point.

Source: WKU


Charlotte Motor Speedway Becomes Pit Stop for Atrium Health Coronavirus Testing

Charlotte Motor Speedway has become the first professional sports venue in the country to serve the community as a remote testing site during the ongoing coronavirus disease 2019 (COVID-19) pandemic.

CHARLOTTE, N.C., March 24, 2020 – For more than 60 years, Charlotte Motor Speedway has been a place for “firsts.” Today, in yet another first, the speedway has become the first professional sports venue in the country to serve the community as a remote testing site during the ongoing coronavirus disease 2019 (COVID-19) pandemic.

In partnership with the speedway, Atrium Health has created a Coronavirus Testing Center at zMAX Dragway, part of the Charlotte Motor Speedway complex. The remote testing site provides a convenient location for residents of northern Mecklenburg and Cabarrus Counties to have their tests performed when ordered by their physician. Atrium Health has several additional sites throughout the Charlotte region, each in locations designed to provide a secure, private environment for patients to be tested.

Testing for COVID-19 is conducted without patients having to get out of their cars, which reduces the possibility of infecting other patients and healthcare workers. Healthcare providers will make appointments and direct patients to designated testing centers where medical professionals will approach the patients at their cars. These tests involve obtaining swabbed samples, which are then tested at Atrium Health’s in-house lab, and patients are typically notified of the results in approximately 24 hours. Atrium Health can test approximately 1,000 samples each day and is one of the only health systems in the nation to have this capability.

“Having these types of remote locations, away from a hospital or other care locations, yet convenient for people in need of testing, is essential to helping contain the spread of the coronavirus,” said Jim Hunter, MD, senior vice president and chief medical officer, Atrium Health. “It’s important to note that patients still need to meet the established criteria for testing by a healthcare provider, which will keep other patients and healthcare workers safe, as well as protect our testing supplies. We deeply appreciate this partnership opportunity with Charlotte Motor Speedway to make a significant impact on the health of our community.”

“At Charlotte Motor Speedway, we work for the fans, salute our military and serve our community,” said Greg Walter, Charlotte Motor Speedway executive vice president and general manager. “During these unprecedented times, we want to support our neighbors and the region with what we can do to keep people healthy. Atrium Health has been a longtime partner of ours and we’re happy to work with them to provide a well-known, accessible and safe place to host this remote testing site for as long as there is a need.”

Atrium Health continues to work to keep the communities it serves safe and informed. The latest information including prevention tips, frequently asked questions and care options are found at www.AtriumHealth.org/Coronavirus:

• COVID-19 Risk Assessment: Answer a few quick questions using a new automated and interactive digital COVID-19 assessment tool to get immediate recommendations on next steps in care.

• Atrium Health Line (704-468-8888): Talk live with an Atrium Health healthcare professional to answer questions, 24 hours, 7 days a week.

• Symptom Checker Chart: Is it COVID-19, the flu, a cold, or seasonal allergies? Click here to help distinguish between typical symptoms of each.

• Virtual Visits: Secure, face-to-face video chat with a trusted healthcare provider from the comfort of home for a reduced cost of $25.

• eVisits: Care through a secure message for minor illnesses like flu or cold for a reduced cost of $10.


About Atrium Health

Atrium Health is a nationally recognized leader in shaping health outcomes through innovative research, education and compassionate patient care. Headquartered in Charlotte, North Carolina, Atrium Health is an integrated network not-for- profit healthcare system with over 70,000 teammates at nearly 40 hospitals and more than 900 care locations. With locations throughout the Carolinas as well as Georgia, Atrium Health is a leading-edge innovator in virtual care and mobile medicine. It provides top-ranked pediatric, cancer and heart care to patients, as well as specialized musculoskeletal programs and organ transplants. Ranked among U.S. News & World Report’s Best Hospitals in seven different specialties, it has also received the American Hospital Association’s Quest for Quality Prize, and the only healthcare system to receive the 2020 CMS Health Equity Award. Its flagship hospital, Atrium Health’s Carolinas Medical Center, is the region’s only Level I trauma center and is consistently rated among the nation’s best. With a commitment to every community it serves, Atrium Health seeks to improve health, elevate hope and advance healing – for all. Last year alone, Atrium Health provided more than $2.07 billion in free an uncompensated care and other community benefits.

About Charlotte Motor Speedway

Celebrating its 60th anniversary season, Charlotte Motor Speedway has set the standard in motorsports entertainment for fans of all ages. Known as America’s Home for Racing, Charlotte Motor Speedway is the only race vacation destination where fans can immerse themselves in the heart of NASCAR country. Visitors can attend one-of-a-kind race spectacles including the NASCAR All-Star Race, Coca-Cola 600 and Bank of America ROVALTM 400; take behind-the-scenes speedway and race shop tours; explore the NASCAR Hall of Fame and drive an 800-horsepower stock car. The 1,000 plus acre speedway complex also includes state-of-the-art facilities zMAX Dragway and The Dirt Track at Charlotte. Through every event and every decade, Charlotte Motor Speedway puts FANS FIRST with a never-ending commitment to enhance the fan experience. That tradition continues with unmatched value through affordable tickets, unparalleled pre-race entertainment and opportunities for fans to see their favorite drivers. For all the latest news and information, visit www.charlottemotorspeedway.com, follow on TwitterFacebook and Instagram or download the Charlotte Motor Speedway mobile app.